Audi 80/Avant (B4)

since 1991-1995 release

Repair and operation of the car



Audi 80/Avant
+ Technical specification
- Engines
   Basic elements
   Lubrication system
   Ventilation of a case
   Visual check of the engine
   Running in of the new engine
   Engine service life
   Nominal and maximum frequency of rotation
   Restriction of frequency of rotation
   Measurement of pressure of compression
   List of malfunctions
   Provorachivaniye of the engine
   Hydraulic pushers
   Works on the GRM gear belt
   List of malfunctions
   Removal and installation of a head of the block of cylinders
   Removal and installation of the engine
+ System of production of the fulfilled gases
+ Cooling system
+ Fuel tank and fuel pump
+ Air filter and airintaking channels
+ System of injection
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Anti-blocking system of brakes
+ Wheels and tires
+ Body electrical system
+ System of ignition
+ Lighting
+ Signaling devices
+ Devices and auxiliary devices
+ Heating and ventilation
+ Body elements
+ Search of malfunctions
+ Specifications





Provorachivaniye of the engine

For a provorachivaniye of a bent shaft of the 4-cylinder engine manually it is necessary to put a key of 22 mm on a generator pulley nut. If the belt slips, it is necessary to press it.


The clamps of a cover of a head of the block of cylinders of the 5-cylinder engine have to be put in the represented sequence at first by the next moments of an inhaling of 5 N • m, then 10 N • m, and in the last turn of 12 N • m.

Sleva: on the 5-cylinder engine the crankshaft can be turned a generator pulley nut (a key of 24 mm). If the belt slips a little, it needs to be loaded with a hand.

On the right: the bent shaft of the 6-cylinder engine is turned the central bolt of a pulley of a bent shaft. As the tool the 12-faced replaceable face head of 24 mm with a graggers or the lever is applied.


VMT is found if the mark "O" appeared on a flywheel under edge of the case of the transmission (shooter).

Sleva: one more mark VMT at 6-cylinder engines is located on a pulley or the lower protective cover of a gear belt (arrow).

On the right: at VMT of the moment of ignition of the first cylinder big openings of adjusting plates on both driving gear wheels of the camshaft are directed to the middle of the engine (shooter).

For carrying out some works it is necessary or to bring a bent shaft into a certain situation, or to turn it.

 PERFORMANCE ORDER

  1. For this purpose in the car with the mechanical transmission on a plain surface it is necessary to include the fifth transfer and to roll away the car a little forward or back.
  2. On the 4-cylinder engine to put a curved cap key on 22 mm on the central nut of a pulley of the generator and to turn the engine through maple a belt. If the belt slips, it needs to be pressed through between pulleys a free hand and by that to pull.
  3. On the 5-cylinder engine to put a rozhkovy wrench of 24 mm on the central nut of a pulley of the generator and to turn the engine in the same way, as 4-cylinder.
  4. On the 6-cylinder engine to put a 12-faced replaceable face head of 24 mm on the central bolt of a pulley of a bent shaft and to turn a bent shaft a graggers or the lever.
  5. Never turn the engine for a bolt of fastening of a gear wheel of a gear belt on distributive to a shaft at the removed casing of a gear belt! The gear belt can jump, result – damages of the engine.

Installation of the cylinder 1 in the provision of the top dead point (TDP) of the moment of ignition

In the four-cycle engine the piston two times come to the top dead point (TDP): the first time at ignition of the let-in gas mixture and the second time after emission of exhaust gases with beginning in conclusion repeated absorption of mix of fuel/air. Usually at various adjusting works VMT of the moment of ignition of the first cylinder is necessary.

 PERFORMANCE ORDER

  1. 4-cylinder and 5-cylinder engines: to uncover, separating the breaker from the ignition distributor, the runner of the distributor of ignition and a protective cover. Again to put on the runner of the distributor and to turn the engine until the contact of the runner is not over a small tag on the edge of the distributor. Thereby VMT is found.
  2. That this business was perhaps more exact probably it will be required to turn a bent shaft a little in one or other party until in in a viewing opening of the transmission marking "About" on a flywheel at edge of a viewing opening appears.
  3. 6-cylinder engine: to remove a casing of a gear belt on the right and at the left (below in this chapter is described).
  4. To turn a bent shaft until both openings of the fixing plates on both driving gear wheels of the camshaft are not established inside the friend opposite to the friend (to one line).
  5. To turn a little a bent shaft in one or other party until in a viewing opening of a cover of the transmission marking "About" on a flywheel at edge of a viewing opening appears.

Removal of a protective cover of the engine

The 6-cylinder engine is supplied with a protective cover which performs noise suppression function. Removal:

 PERFORMANCE ORDER

  1. To turn four high-speed locks the big screw-driver on 90 ° to the left.
  2. To remove a protective cover.

Removal of a cover of a head of the block of cylinders

 PERFORMANCE ORDER

  1. 4-cylinder engine: on the 66 kW engine to remove the air filter.
  2. To remove a hose for removal of air from a case. To disconnect a plait of wires if is available.
  3. To weaken a cable of the drive of "gas" and to extend it from a support.
  4. To turn off fixing nuts.
  5. To remove overlays of rigidity.
  6. To lift a cover.
  7. If necessary to remove a maslootrazhatel.
  8. 5-cylinder engine: to remove a hose of the amplifier of brakes from an inlet collector.
  9. To remove the top part of an inlet collector and vpryskny nozzles (the head "System of injection KE-III-Jetronic").
  10. To remove the distributive valve of stabilization of idling.
  11. To turn off fixing nuts, to remove overlays of rigidity.
  12. To uncover.
  13. 6-cylinder engine: to remove protection of the engine.
  14. To turn off lock bolts.
  15. To raise a cover.
  16. If necessary to remove a maslootrazhatel.
  17. At installation to put new laying.
  18. 4-and 5-cylinder engines: not to forget about a sheet overlay of rigidity under fixing nuts.
  19. 6-cylinder engine: to slightly grease laying of a cover of a head of the block of cylinders on internal and outer side with silicone antifrictional means of D 007 000 04.
  20. To put on all four sides between sealing laying of a head of the block of cylinders and a cover of the bearing of the camshaft it is a little "Silimate" AMV 174 004 01 from a warehouse zapchaty Audi. To watch that at the same time the opening for oil below on a camshaft bearing cover was not hammered.
  21. All types of engines: it is crosswise to tighten the moment 10 N • m of a nut or bolts, since the middle of a cover.


warning signs of miscarriage





http://b3-b4.ru/