Audi 80/Avant (B4)

since 1991-1995 release

Repair and operation of the car



Audi 80/Avant
+ Technical specification
+ Engines
+ System of production of the fulfilled gases
+ Cooling system
+ Fuel tank and fuel pump
+ Air filter and airintaking channels
+ System of injection
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Anti-blocking system of brakes
+ Wheels and tires
+ Body electrical system
+ System of ignition
+ Lighting
+ Signaling devices
+ Devices and auxiliary devices
+ Heating and ventilation
- Body elements
   Front bumpers
   Forward part of the car
   Cowl
   Wings
   Moldings
   Doors
   External rear-view mirrors
   Forward and back flew down
   Trunk lid at the sedan
   Back door of the versatile person
   Rear bumper
   Movable hatch
   Clearing of openings for a water drain
   Control of anticorrosive protection of the bottom of a body
   Salon
   Seats
+ Search of malfunctions
+ Specifications





Salon

Removal of the left shelf

For removal of a shelf to weaken bolts with 2 on 5 at the left. At installation to insert a shelf ahead into guides (the position 1 shows one of them).

The left lower part of a covering of the dashboard integrated with a shelf has to be removed almost in all cases when access to a reverse side of the dashboard is necessary.

 PERFORMANCE ORDER

  1. Narrow face key to turn out four screws around a shelf.
  2. To cast away a little a shelf down and to extend to itself.
  3. At installation to insert a first line of a covering into both directing to the bottom of the car and near pedals.
  4. Not too hardly to tighten screws.

Removal of a ware box

The ware box (1) is attached by the loops (2 and 3) to the dashboard (arrow). On an illustration the box is shown in unassembled form.


 PERFORMANCE ORDER

  1. To turn out both fixing screws of a loop of a ware box at bottom edge of the dashboard.
  2. To slightly wring out stoppers of a ware box inside and to cast away a ware box down.

Removal of the lower part of the central console

Removal of a back part of the central console: to remove a level (1), to disconnect a covering of the lever of the parking brake (3), to disconnect an earring (arrows) on the handle (2) from a clamp.


 PERFORMANCE ORDER

  1. To tighten the parking brake.
  2. To wring out the screw-driver fixing laying of a cover of the lever of the parking brake and to separate from a floor.
  3. In front slightly to raise a covering, to wring out a lever earring up and to extend the lever forward.
  4. To raise the decorative panel in front of the lever of the parking brake. At the same time to hook the upper edge the small screw-driver.
  5. To turn out six fixing bolts which are under the panel.
  6. To remove a back ashtray.
  7. To turn out two six-sided bolts under an ashtray.
  8. To pull a console part for a first line up and to remove it in the direction forward over the lever of the parking brake.

Removal of a forward part of the central console

Removal of a forward part of the central console: to turn off a head of the lever of gear shifting (2), to weaken a bolt on a casing of the lever (1). (3) – forward guides.


Shooters show on two bolts located in a heating panel cut which need to be weakened for removal of the central console.


 PERFORMANCE ORDER

  1. To disconnect a wire on "mass" of the accumulator.
  2. To completely remove a back part of the central console.
  3. To remove the lever of gear shifting or the lever of the selector.
  4. To turn off a bolt with crosswise shliyets on the rear edge of the console and to remove a cover of the handle of gear shifting or a covering.
  5. To disconnect all three regulators of heating/ventilation.
  6. To unscrew two screws of the panel of heating and to remove it.
  7. At the cars equipped with the automatic conditioner completely to remove the control panel.
  8. Below on the right and at the left in a cut of the panel of heating to turn out on one screw.
  9. To wring out the console with an ashtray down, at body option with additional devices to remove in the direction a narrow decorative plate down.
  10. In the direction to disconnect the console from the control panel back.
  11. If necessary to disconnect wires.
  12. At installation guides on the dashboard and the central console have to enter one another.







http://b3-b4.ru/