Audi 80/Avant (B4)

since 1991-1995 release

Repair and operation of the car



Audi 80/Avant
+ Technical specification
+ Engines
+ System of production of the fulfilled gases
+ Cooling system
+ Fuel tank and fuel pump
+ Air filter and airintaking channels
+ System of injection
+ Coupling
+ Transmission and transmission
+ Suspension bracket and steering
+ Brake system
+ Anti-blocking system of brakes
+ Wheels and tires
+ Body electrical system
+ System of ignition
+ Lighting
+ Signaling devices
- Devices and auxiliary devices
   Check of indicators and signaling devices
   Elements of a combination of devices
   Speedometer
   Tachometer
   Hours
   Indicator of amount of fuel
   Indicator of temperature of cooling liquid
   Voltage stabilizer
   Additional devices
   The top indicators in a combination of devices
   Indicator of cooling liquid
   Indicator of the brake system
   Oil pressure indicator
   Indicators of indexes of turns
   Lower indicators
   Indicator of a charge of the rechargeable battery
   Indicator of indexes of turn of the trailer
   Safety cushion indicator
   Indicator of anti-blocking system
   Indicator of driving beam
   Indicator of the parking brake
   System of self-examination
   Switches
   Ignition lock
   Check of switches
   Buzzer of shutdown of lighting and radio
   Lighter
   Heating of back glass
   Check of screen wipers and windscreen washers
   Screen wiper engine
   List of malfunctions
   Screen wiper of back glass
   List of malfunctions
   Replenishment of a washer reservoir of glasses
   System of washing of headlights
   Audio system
   Antenna of back glass
   Electric regulation of external rear-view mirrors
   System of locks with the central management
   Power windows
+ Heating and ventilation
+ Body elements
+ Search of malfunctions
+ Specifications





List of malfunctions

Screen wiper

Malfunction
Its reason
Than to help
A. The screen wiper does not work 1. The safety lock fused
2. The unloading relay is faulty
3. The screen wiper drive crank became loose
4. Giving of power supply on black gray wire from the block of safety locks to the screen wiper switch is interrupted
5. Connection on "mass" of a screen wiper is interrupted
6. The screen wiper engine fused
To replace
To check the relay
To tighten
To check a wire
To check a wire
To replace
B. Brushes of a screen wiper do not work at the first speed 1. Defective plug 53 engines of a screen wiper
2. Conducting of plugs 53a/5 in the screen wiper switch is interrupted
To replace the screen wiper engine
To replace the screen wiper switch
C. Brushes of a screen wiper do not work at the second speed 1. Conducting of the plug 53b from the screen wiper switch to the car engine is interrupted
2. Conducting of plugs 53a/53 in the screen wiper switch is interrupted
3. Defective plug 53b of the engine of a screen wiper
To check conducting
To replace the screen wiper switch
To replace the screen wiper engine
D. Brushes of a screen wiper work only at the second speed Conducting of the plug 53 from the screen wiper switch to the car engine is interrupted To check conducting
E. Brushes of a screen wiper do not come back to a starting position 1. Conducting of the plug 53e from the screen wiper switch to the car engine is interrupted
2. The screen wiper engine is faulty
To check conducting
To check with a control lamp: between the plug 53 and "weight" the lamp has to burn constantly. Between the plug 53e and "weight" the lamp has to go out shortly before achievement by brushes of an initial position. At the return check between plugs 53e and to a positive conclusion of the accumulator the lamp has to flash shortly before achievement by brushes of an initial position. Otherwise it is necessary to replace the engine
F. Brushes of a screen wiper do not work in the faltering mode 1. The screen wiper/windscreen washer relay is faulty
2. Conducting of the plug J between the switch of a screen wiper and the engine of the car is interrupted
3. The contact of J in the screen wiper switch is defective
To replace
To check conducting
To replace the screen wiper switch
G. It is impossible to switch off a faltering operating mode 1. See E 1
2. See F 1
3. The contact of J in the switch of a screen wiper does not work
4. Short circuit of conducting of the plug J to the screen wiper switch
To replace the switch
To put conducting in order
H. Brushes of a screen wiper leave water on glass after washing Cm F 1  
J. The screen wiper does not remain after switching off in starting (parking) position or only for a short time Bad coupling at the sliding contact in the screen wiper engine To disassemble the screen wiper engine, to smooth out contacts. If necessary to replace the engine

The engine of a screen wiper or the bringing wire are faulty?

Will help to find out existence of malfunction of the engine of a screen wiper or conducting to you the following check:

 PERFORMANCE ORDER

  1. To remove the left part of a covering over the water catching capacity behind in a motor compartment, having opened before it a rotary latch. If necessary in addition to remove the left screen wiper.
  2. To separate the multicontact plug of the engine of a screen wiper.
  3. Now it is necessary to lay two auxiliary wires. One from a positive conclusion of the accumulator to the plug 53 or 53b (connections of black-gray or greenish-yellow wires).
  4. The second wire is laid from a negative conclusion of the accumulator to the plug of 31 engines of a screen wiper (there where the brown wire was inserted).
  5. The screen wiper has to work at the first or second speed, depending on the plug chosen for connection now. Otherwise malfunction of the engine of a screen wiper is available.
  6. If the screen wiper began to work, so malfunction is covered in the switch or in the bringing conducting.

Removal of the engine of a screen wiper

 PERFORMANCE ORDER

  1. To include ignition and screen wipers.
  2. When the lever of a screen wiper is on glass on a half of the course (that is under 45 °), to switch off ignition and by that to detain a screen wiper in this situation.
  3. To remove screen wiper levers.
  4. To remove a black plastic cover of the water catching capacity, having opened the rotary switch and having removed back sealing laying of a motor compartment.
  5. To turn out two six-sided bolts above on axes of screen wipers and one below at the engine.
  6. To separate the multicontact plug of the engine of a screen wiper.
  7. To remove screen wiper levers together with the engine.
  8. To disconnect drafts from screen wiper axes
  9. To turn out three screws at the screen wiper engine. To reach all screws, it is necessary to turn an engine crank.

Installation of the new engine of a screen wiper

 PERFORMANCE ORDER

  1. To connect to the electrician of the engine and to leave to work short time. To switch off and wait until it returns to a starting position.
  2. To install the engine on the console, to put on a driving crank and levers of screen wipers.
  3. The driving lever to the left axis of a screen wiper is put on an engine crank from below, the right axis of a screen wiper connects to an engine crank from above.
  4. Now so to tighten an engine crank that he got up in the situation shown in the drawing on the right below.
  5. If not to enshrine a driving crank in this certain provision, then at a start of motion levers will move down.
  6. Installation of levers of brushes of a screen wiper: fixing screws should be tightened quite poorly because they sit in plastic plugs!







http://b3-b4.ru/